अक्सर पूछे जाने वाले प्रश्न

हमने विभिन्न प्रकार की बाइक के अनुरूप कई स्टेडीरैक बनाए हैं। हमारे रैक पर माउंटिंग ब्रैकेट सभी समान हैं, केवल बाहों में विभिन्न बाइक आकारों को पूरा करने के लिए अलग-अलग लंबाई और चौड़ाई है। अपनी बाइक के लिए सही स्थिरक खोजने के लिए, कृपया अपनी बाइक को सही ढंग से मापने का तरीका जानने के लिए हमारे उत्पाद पृष्ठ पर जाएं।

एक स्ट्रिकरैक के साथ, अपनी बाइक को उठाने या बाजीगरी करने की कोई आवश्यकता नहीं है। बस अपने बैक ब्रेक को निचोड़ें, हैंडलबार पकड़ें और बाइक को पीछे के पहिये पर ले जाने के लिए पीछे की ओर चलें। हमारे ईबाइक रैक में भारी बाइक उठाने पर हमारा प्रदर्शन देखें।

हां - हमारे सभी पांच रैक बाईं और दाईं ओर 160 डिग्री तक धुरी बनाते हैं।

The rear wheel rest/bracket is designed to prevent the bike from swinging from side to side when pivoting a bike in the rack. This keeps bikes safe and secure and eliminates damage to the wall. Your tyre is only required to have partial contact with the rest for it to perform its function. Simply place the rear wheel to the side you wish to pivot the bike.
It works universally with all tyre widths, including fat tyres. Narrow tyres will generally sit deeper in the bracket (more than wide tyres).

एक स्थिर में बाइक लटकाने से आपके फ्रेम, कांटे या पहियों को कोई नुकसान नहीं होगा। बाइक के फ्रेम का कोई भी हिस्सा रैक को नहीं छूता है, केवल सामने का टायर, जो स्टील आर्म्स में घिरा हुआ है।

Steadyrack are assembled using a specific tension for the nuts that hold the central spine to the top and bottom mounting brackets. (torque setting = 5mm) This setting is designed to give sufficient tension to the pivot to ensure bikes can be loaded on any angle without the rack moving around too much. When you remove the 2 plastic caps from the top and bottom the nuts are exposed. You can loosen both nuts and it will free up the rack more and equally you can tighten them to lock the rack into position. We recommend you maintain them so the racks are stiff but can still be pivoted.
The rack can be quite stiff when you use it for the first few times then it loosens up a bit. This is due to the type of fiber washers we use to assist with the stiffening effect.

The racks are designed to cover a wide range of tyre widths. Some wider tyres will fit tightly in between the arms of the rack. As long as you can still release them by pulling on the handlebars with minimal force it's fine. It actually helps to ensure the bikes can't be easily dislodged. If you find you have to use excessive force to remove the bike you may need to change to a larger version of the racks.

No, it's not possible to lock the rack solid in one position. You can tighten the nuts sufficiently that the rack will be very hard to pivot which will effectively hold it in the one position. To do this you need to remove the 2 plastic mounting bracket covers (end caps) and tightening the 2 nuts that attach the central pivot bar to the mounting brackets. We recommend you check your fixings to your wall carefully and make sure they are very secure if you do this as any pressure sideways will put extreme pressure on the mounting brackets fixings.

No, you can load and unload the bike at any angle provided that the central pivot bar nuts are set to the factory setting of 5mm.

It really depends on the width of your handlebars and the pedals. It will fold until the handlebars touch the wall but not quite 90 degrees or flat to the wall. For a normal road bike bar, we would allow about 400mm or around 16 inches, and for a MTB with wider bars probably around 1m or 39 inches (give or take).

अपनी बाइक को स्टेडीरैक के साथ लंबवत रूप से संग्रहीत करके, आप प्रत्येक दिशा में 160 डिग्री तक बाइक को धुरी बनाने में सक्षम होंगे, उन्हें दीवार के करीब रखेंगे। यह न केवल फर्श की जगह बचाएगा, बल्कि छोटे क्षेत्रों में अधिक स्थान भी बचाएगा, जो कार के साथ अंतरिक्ष साझा करते समय सहायक होता है। हाथ डिजाइन के साथ संयुक्त होने पर रैक को साइड-टू-साइड धुरी बनाने में सक्षम होने के कारण, किसी भी अन्य उत्पाद की तुलना में बहुत अधिक स्थान लचीलापन और स्थान की बचत की अनुमति मिलती है। स्टीडीरैक्स पेटेंट और क्रांतिकारी डिजाइन आपके मूल्यवान फर्श स्थान को बचाने में मदद करता है और प्रत्येक रैक के बीच 350 मिमी तक कम के साथ लगभग किसी भी दीवार पर लगाया जा सकता है। घूर्णन / धुरी कार्रवाई के कारण, एक स्थिर में संग्रहीत बाइक को अतिक्रमित किया जा सकता है और जब उपयोग में नहीं होता है, तो हाथ बस और भी अधिक स्थान के लिए मुड़ जाते हैं।

The Steadyrack won’t work with a rear wheel because of the derailleur and gears.  One of the main features is the way you roll your bike in and out; you don’t use a lifting action so you can do away with hooks. It’s very easy to balance the bike on the back wheel and push forward until the front tire engages and then it just rolls up and drops into the 2 v shaped cradling points. The bike is then resting on a cushioned tire not hanging by a hook.

हमने आपकी प्रतिक्रिया सुनी है, और अब हमारे पास हमारे रियर टायर रेस्ट्स के लिए एक नया और बेहतर डिज़ाइन है, जिसमें फैट रैक के लिए एक बड़ा रियर टायर रेस्ट भी शामिल है। रियर टायर रेस्ट अब तीन अलग-अलग आकारों में उपलब्ध हैं: छोटे, मध्यम और बड़े। स्मॉल टायर रेस्ट क्लासिक रैक और फेंडर रैक में संग्रहीत बाइक के साथ संगत है। मीडियम टायर रेस्ट माउंटेन बाइक रैक में संग्रहीत बाइक के साथ संगत है। लार्ज टायर रेस्ट फैट रैक में संग्रहीत बाइक के साथ संगत है।

क्षमा करें, लेकिन वर्तमान में हमारे पास कोई समाधान नहीं है जो आपके टायर के आकार में फिट बैठता है और फेंडर / मडगार्ड के लिए भी समायोजित करता है। यदि आपका मडगार्ड / फेंडर एक क्लिप-ऑन प्रकार है जो धातु की छड़ के साथ सामने के धुरे से जुड़ा नहीं है, तो इसे फैट रैक के साथ ठीक काम करना चाहिए।

हम प्रत्येक रैक के लिए निर्धारित वजन सीमा से अधिक की सिफारिश नहीं करते हैं। फेंडर रैक पर एक भारी बाइक को घुमाने का अतिरिक्त वजन और बल संभवतः बाहों को मोड़ने का कारण बन सकता है। प्रत्येक रैक के लिए उल्लिखित वजन पर काम करना रैक या आपकी बाइक को नुकसान पहुंचाने की किसी भी संभावना को दूर कर देगा। यदि आपकी बाइक भारी है और इसमें फेंडर या मडगार्ड हैं, तो हमारे ईबाइक रैक को देखें।

स्टेडीरैक क्लासिक, फैट, फेंडर और माउंटेन बाइक रैक सभी केवल ब्लैक में आते हैं। हालांकि, आप हमारे एंड कैप्स के साथ अपने रैक को कस्टमाइज़ कर सकते हैं, जो लाल, नीले, हरे, पीले, नारंगी और ग्रे रंग में आते हैं। हमारे एंड कैप इंस्टॉलेशन वीडियो यहां देखें।

Yes - all our racks are compatible with most types of locks, including chain, cable and D-locks. We have introduced a lock bracket and D lock and cable which is available for purchase on our website. It is also important that you do not rely on the rack arms, as the bolts holding these to the rack frame can be undone.

Great question! The best process is to put the rear brake on and walk backwards to raise the bike up onto the rear tyre. This ensures that there is minimal effort used and absolutely no lifting required.

जैसा कि स्टेडीरैक को अंतिम नो लिफ्ट स्टोरेज समाधान के रूप में डिज़ाइन किया गया है, आप आश्वस्त हो सकते हैं कि अपनी बाइक को स्टेडीरैक में संग्रहीत करने से आपकी पीठ पर कोई तनाव नहीं होगा। नो लिफ्ट डिज़ाइन भारी बाइक को स्टोर करना भी आसान बनाता है। एक स्थिर ा के लाभों के बारे में यहां और पढ़ें।

हां - हमारे पास एक ईबाइक रैक है जो फेंडर या मडगार्ड के साथ भारी इलेक्ट्रिक बाइक स्टोर करने के लिए एकदम सही है।

The Fender Racks will suit exactly the same bikes as the Classic Rack except the Fender rack will also work with bikes that have fenders or mudguards, whereas the Classic is only suitable for bikes without fenders and mudguards. The Fender rack will also only accommodate for bikes up to 25kg/55lbs.

Due to the small space between the front tyre and the down tube on TT bikes you would need a Fender Rack or eBike Rack.

Unfortunately, any wheels that are less than 16" in diameter will not fit in any of our Steadyracks. If you store a bike with smaller wheels, you risk not having the tyre come into contact with the two V-shaped cradling points, meaning the fork will rest on the rack before the tyre.

We found some success with placing Velcro straps on the bottom arm to shorten the distance between the 2 points, however the bikes are not as stable, and you would need to strap the wheel to the upper arm of the rack with Velcro as well.

Some of the newer plus size MTB tyres have extra-large shoulder lugs (tread) which take the overall width past the actual measurement marked on the sidewall. If your tyres have extra wide lugs you can still work to our sizes in our guide but it will be a tighter fit and will mean you have to push it into the rack and pull harder on the bike to dislodge it when you remove it. So yes it should fit in a mountain bike rack but will be a firm fit. If you don’t want to do that you should go to the next size up to the Fat Rack. The bike will sit nicely in the rack but the front wheel may fall to one side slightly due to the larger gap but it will be very easy to unload.

We don’t recommend exceeding the set weight limits for each rack. The extra weight and force of rolling a heavier bike onto the Fender Rack could possibly cause the arms to bend. Working to the weights outlined for each rack will remove any possibility of damaging the rack or your bike. If your bike is heavier and has fenders or mudguards, check out our eBike Rack.

We have 5 models to suit a wide variety of bikes. The best model for your bike depends on the wheel rim diameter and tyre width of your front wheel. Please visit our website to work out which rack you need.

We do not recommend storing bikes with wheels less than 16” in diameter in our racks. If you store a bike with smaller wheels, you risk not having the tyre come into contact with the two V-shaped cradling points, meaning the fork will rest on the rack before the tyre.

We found some success with placing Velcro straps on the bottom arm to shorten the distance between the 2 points, however the bikes are not as stable, and you would need to strap the wheel to the upper arm of the rack with Velcro as well.

Yes! This is a common concern for many bike owners with these types of brakes and suspension. When your bike is hung up vertically, the fluid in your forks will run towards the seals and keep them lubricated. This will prolong their use, so it's actually good for your bike and forks to hang it vertically on our bike racks. If you have hydraulic brakes on your bike the fluid will run down when the bike is hung, so we advise pumping the brakes a few times when you take the bike off the rack if it's been there for a while. The shocks shouldn't leak when the bike is hung up, however if they do it's a good indication that the seals may need replacing. Read our blog post for more information about storing bikes with hydraulic brakes in Steadyracks.

One of the main features of our design is the fact that it is the most suitable rack for carbon wheels. There is less pressure on the bike than riding it and it is certainly better than hooks. The wheel is cradled between the 2 v shaped cradling points created when the arms are folded down and the tire cushions the wheel and bike. There should be absolutely no need to do any maintenance on your rims or wheels if you use a Steadyrack.

Steadyracks are actually the perfect solution for storing carbon frame bikes and wheelsets! This is because our racks cradle the whole front wheel tyre, meaning there is no direct contact with the wheelset or bike frame. Additionally, there is less risk of damage from and to surrounding bikes as the racks are made to pivot and are hung by rolling the bike into the cradle instead of lifting the bike onto a hook.

Our MTB rack is wider and longer to accommodate the larger tyres on mountain bikes, however your 1.75 inch tyres will still sit securely in the MTB rack. You'll find there's some slight movement of the bike within the rack due to the rack being larger than the Classic Rack, however the bike is still completely secure within the MTB rack if you wish to use that one.

हमारे डिजाइन गाइड और स्पेसिंग गाइड हमारी वेबसाइट पर डाउनलोड करने के लिए उपलब्ध हैं ।

प्रत्येक रैक के साथ आपूर्ति की जाती है:

• ब्रैकेट, जिसे आपके रियर व्हील एक्सल के अनुरूप दीवार पर तय किया जाना चाहिए (अधिक जानकारी के लिए हमारे इंस्टॉलेशन निर्देश और वीडियो देखें)।
• 4x bolts and 4 x wall anchors/plugs for installing the rack (the wall anchors/plugs are for masonry use only).
• 2x smaller screws and 2 x anchors/plugs for the rear tyre rest/bracket (the wall anchors/plugs are for masonry use only).
• स्थापना निर्देश
• 1 साल की मुफ्त वारंटी
  

There are four mounting holes on each mounting plate. You should only use two of these holes to fix your rack to the wall or frame. The two vertically aligned holes are for fixing to studs and the two horizontal aligned holes are for fixing into masonry.

अपने रैक को स्पेस करना इस बात पर निर्भर करता है कि आप फर्श की जगह, दीवार की जगह या दोनों को बचाना चाहते हैं या नहीं। हमने मदद करने के लिए एक आसान वॉल प्लेसमेंट गाइड बनाया है ।

फर्श स्थान बचाओ 

यदि आप फर्श की जगह बचाना चाहते हैं, तो आपको अपने रैक को और अलग करना होगा ताकि आप उन्हें दीवार के करीब मोड़ने के लिए धुरी का उपयोग कर सकें। यदि आप उन्हें जितना संभव हो उतना मोड़ना चाहते हैं तो उन्हें काफी दूर तक स्पेस करना सबसे अच्छा है ताकि बाइक मुड़ने पर इसके बगल के रैक को न छुए। 

दीवार स्थान बचाओ 

यदि आप दीवार स्थान को सहेजना चाहते हैं, तो आप उन्हें एक साथ लटका सकते हैं। ध्यान दें, वे एक-दूसरे के जितने करीब होंगे, उतना ही कम वे बाइक को छूने से पहले धुरी बनाने में सक्षम होंगे। हैंडलबार को एक-दूसरे को छूने से बचने के लिए आपको ऊंचाइयों (एक ऊपर और एक नीचे) को स्थिर करने की भी आवश्यकता हो सकती है। हमारे डिज़ाइन के बारे में अच्छी बात यह है कि आप अपनी बाइक को 350 मिमी के करीब और कुछ मामलों में और भी करीब रख सकते हैं, लेकिन आप अभी भी बाइक को दोनों तरफ से जोड़कर एक्सेस स्पेस बना सकते हैं।

दोनों को बचाएं

हमने पाया है कि अपने रैक को सभी समान ऊंचाई और लगभग 600 मिमी या 2 फीट की दूरी पर रखने से आपको दोनों का थोड़ा सा लाभ मिलेगा। बाइक को एक-दूसरे के शीर्ष पर मोड़ा जा सकता है, लेकिन केवल आपके फर्श स्थान में लगभग आधा हिस्सा होगा यदि वे सही कोण पर थे। अक्सर इसका मतलब है कि आप अपनी बाइक के साथ अपने पार्किंग स्थान में एक कार प्राप्त कर सकते हैं।

यह केवल एक गाइड है, इसलिए हम अनुशंसा करते हैं कि आप अपनी बाइक के आकार, हैंडलबार के प्रकार और चौड़ाई और आपके पास उपलब्ध दीवार और फर्श स्थान की जांच करें। स्पेसिंग के बारे में अधिक जानकारी के लिए हमारे वॉल प्लेसमेंट गाइड पेज पर जाएं।

All Steadyracks are supplied with M8 Hex bolts and 10mm x 50mm masonry wall plugs for the racks and M6 screws and8mm x 35mm masonry wall plugs for the rear tyre rest. Wall plugs are for masonry use only. You will require a 10mm masonry drill bit for the 10mm wall plug, and an 8mm masonry drill bit for the 8mm wall plug.

Please visit our Installation Advice page for detailed instructions.

As metric fixings don't always have an exact drill bit size match in various regions, if you are unsure we advise you to take the wall plugs provided with your rack to your local hardware store or expert, and ask them for the right size drill bit for your equipment and installation.
Please keep in mind you will need a different size for the rear tyre rest.

It is recommended that you use all four M8 screws, and both M6 screws. Each Steadyrack comes with 4x bolts and plugs for installing the rack and 2x smaller screws and plugs for the rear tyre rest. There are four mounting holes on each mounting plate and you will only need to use two of these holes to fix your rack to the wall or frame. The two vertically aligned holes are for fixing to studs and the two horizontally aligned holes are for fixing into masonry or other solid surfaces. Steadyracks cannot be fixed to any fragile surface including drywall, gyprock, plasterboard etc. They must be fixed to structurally sound surfaces capable of taking the weight of the bike and rack. Visit our Installation advice page for detailed instructions.

As long as the door is solid and not hollow then yes and the fixings provided are suitable to install on to a solid timber door.

You can fix rails across the studs at your preferred mounting height and then you can space your racks along the rails. Another option is to fix a sheet of plywood (10-13mm, or 1/2 inch thick) across the top of your wall lining or studs and then screw your racks to the ply in the exact location you want them.

No.
Steadyracks can be installed into any structurally sound vertical surface.
It is NOT recommended that you install Steadyracks into Plasterboard or Drywall (also known as Gyprock). Fixing to Drywall, Plasterboard or Gyprock alone voids our warranty. Your racks must always be fixed to a suitable structural material capable of supporting the weight of the rack and the bike. The wall plugs/anchors supplied are for masonry use only.

Steadyracks can be installed into any structurally sound vertical surface. Fixings are provides for installing to Timber or Masonry (brick/concrete). If you wish to install the rack to any other type of surface - such as steel you will need to purchase additional fixings.
It is NOT recommended that you install Steadyracks into Plasterboard or Drywall (also known as Gyprock). Fixing to Drywall, Plasterboard or Gyprock alone voids our warranty. Your racks must always be fixed to a suitable structural material capable of supporting the weight of the rack and the bike.

हम अपने स्टेडीरैक बाइक रैक के साथ रियर व्हील ब्रैकेट / रेस्ट स्थापित करने की सलाह देते हैं, लेकिन अगर परिस्थितियां आपको इसे स्थापित करने से रोकती हैं, तो रैक अभी भी आवश्यकतानुसार प्रदर्शन करेगा। आप पा सकते हैं कि आपका रियर व्हील बाकी के बिना सामान्य से अधिक चलता है, हालांकि यह महत्वपूर्ण नहीं है कि इसे स्थापित किया जाए।

Ideally no. The bike should be suspended above the floor to allow it to freely pivot. Bikes will come in different lengths and therefore different mounting heights which is why we suggest measuring your bikes first by following our installation guide. Refer to our installation instructions for how to work out your optimum mounting height.

All bikes will vary in their ideal mounting height. Refer to our installation guide for how to work out your optimum mounting height.

If you install your racks anywhere they will be directly exposed to the elements including anywhere outside it will void our warranty. They will show signs of rusting and the metal will become dull over time however the functionality won’t be affected at all provided our regular care and maintenance instructions are followed. The plastic is UV treated and should not change appearance as long as it’s not in direct sunlight.

Using Steadyracks to transport bikes is possible, however, it will void the warranty of the rack if done. If you decide to proceed with using the racks to transport bikes, the bikes must be tied to the racks using velcro straps or similar, to prevent excessive load being placed on the rack during transit. If the bikes bounce up and down when stored in the rack, this can cause the arms to bend and bike to dislodge.

The two vertical holes are for timber installation and the two horizontal holes are for masonry installation.

It is possible to install a tandem bike in a Steadyrack. However, the rack will need to be mounted higher to allow for the length of the tandem bike. You also need to ensure that the tandem bike doesn't exceed the maximum weight limit of the rack you have chosen. Please note, it can be more difficult to mount a tandem rack in a Steadyrack due to the length of the bike.

We recommend a minimum of 600mm between racks for best use of the pivot action while saving space but you can mount them as close as 350mm if you stagger the heights. Staggering the heights will make mounting and dismounting slightly more difficult but is a great space saving option. We do recommend you mount each rack at the best height for that bike based on our installation instructions.

Installing your Steadyrack using tamper proof bolts will provide a higher degree of security to prevent theft. We have also introduced a lock bracket and D lock and cable which is available for purchase here. It is also important that you do not rely on the rack arms, as the bolts holding these to the rack frame can be undone. We also recommend not leaving bikes in out of the way public or vulnerable places even when locked as it is almost impossible to prevent a professional thief from stealing a bike using cordless power tools.

Yes the Australian standards are 400mm centres for dynamic racks which ours are. Our spacing recommendations are not designed to comply with any standards or regulatory requirements in any country. These are a global recommendation based on the optimum spacing for our products without sacrificing any of the functionality, features or ease of use of our design. Even though our recommendations may outperform some design regulations and standards they are not a substitute or accredited variation to any standards. If standards or regulations exist it’s advisable to check the requirements in a specific location first to ensure the design of the installation meets those standards.

No the racks are not made from stainless steel. The steel is a mild steel and its Zinc Coated or chrome plated depending on which model you choose.

The racks are made from mild steel and UV treated plastic all of which is fully recyclable.

Our racks are not made from recycled products, however, all of our racks are made from recyclable materials as well as all of our packaging.

Our preference would be to manufacture in our home country Australia however we are not able to produce our products cost effectively here. Even though we don’t manufacture at home we are employing staff, consultants, and service providers in many countries including our headquarters in Australia; if it weren’t for our Chinese factory we would not have a business and we would not be employing anyone.  

Yes – the warranty lasts for a period of one year effective from the purchasing date. You may also register online to extend the warranty to five years. Please read our warranty page on our website for full information.

We work hard to ensure that Steadyrack is manufactured to the highest standard. However if you find a fault or you are dissatisfied with your Steadyrack for any reasons, please visit our website to complete our returns form.
If you change your mind, you have 90 days to return your Steadyrack products in new, unmounted condition. Please note, any return shipping costs must be covered by the customer as agreed to in the terms and conditions when purchasing on our website.

हम यूरोप, यूके, कनाडा, यूएस और ऑस्ट्रेलिया में स्थित हमारे गोदामों में रिटर्न (जो हमारी रिटर्न नीति का अनुपालन करते हैं) स्वीकार करते हैं।

एक बार ऑर्डर संसाधित हो जाने के बाद इसे रद्द नहीं किया जा सकता है और इसके बजाय आइटम को रिटर्न नीति के अनुसार स्टेडीरैक को वापस किया जाना चाहिए। 

खरीदार विक्रेता की पूर्व लिखित सहमति को छोड़कर विक्रेता के साथ दिए गए आदेशों को निलंबित नहीं कर सकता है और फिर केवल तभी जब खरीदार इस तरह के निलंबन या रद्दीकरण के कारण हुए सभी नुकसान के लिए विक्रेता को प्रतिपूर्ति करता है, जिसमें बिना किसी सीमा के, सभी आकस्मिक और परिणामी नुकसान और उससे उत्पन्न होने वाले खर्च शामिल हैं। किसी भी आदेश को निलंबित या रद्द करने के लिए खरीदार के निर्देश को खंडन के रूप में माना जा सकता है, जिससे खरीदार को नुकसान, व्यय और अन्य नुकसान के लिए तुरंत उत्तरदायी बनाया जा सकता है।

If you can please provide support@steadyrack.com with the below information, we will add your extended warranty.

- Name
- Email
- Phone number
- Country
- City
- Post code / zip code
- Date of purchase
- Where you purchased
- Which racks you bought
- Would you like to join our marketing mailing list?

It isn’t uncommon for couriers to split parcels into different consignments if there is more than one carton in a shipment. Your shipment has in this instance. The second consignment of your shipment will be delivered 1-2 business days after the first. If you still have not received your final shipment, please contact Steadyrack Support and we will endeavour to resolve the issue for you.

Please send an email to support@steadyrack.com and we will be able to provide you with information about any dealers near you. 

We can ship products anywhere in the world. If your city/country is not listed on our site please contact support@steadyrack.com with your details and we can arrange a shipping quote for you. 

हमारे पास दूर-दूर तक घरों और व्यवसायों में जितनी जल्दी हो सके अपनी बाइक रैक भेजने के लिए दुनिया भर में गोदाम हैं। हम यूरोप, ब्रिटेन, कनाडा, अमेरिका और ऑस्ट्रेलिया से बाहर भेजते हैं। हमारे अनुमानित शिपिंग टाइमफ्रेम देखें और यह देखने के लिए कि क्या आपका देश मुफ्त शिपिंग के लिए योग्य है।

Shipping times and deliveries vary depending on your country, region and location. Your estimated shipping delivery time will show at the checkout. However, please keep in mind that these may not take into account courier operating days, public holidays and other delivery variables. Once you have placed your order online, it can take from 1 – 3 business days to process your order.

Please visit our Dealer or Distributor page and complete the form and one of our sales team members will be in touch shortly.

The reason you have received two different models, is because we recently made a slight tweak from the V-shape to the U-shape. This is a completely aesthetic tweak and both rear tyre rests that you received are functionable. The V-shape has been discontinued, so if you wish to replace them with the U-shape rest, then we are happy to offer you the new U-shape rest valued at $9.99, free of charge, if you are happy to cover the shipping costs.

Steadyrack Classic, Fat, Fender, eBike and Mountain Bike Racks all come in Black only. However you can customise your racks with our End Caps, which come in red, blue, green, yellow, orange, and grey.

No, this is a prototype that is still in a research and development stage.

हाँ हमारे रैक अपार्टमेंट इमारतों के लिए आदर्श हैं जहाँ पार्किंग एक सुरक्षित वातावरण में है और सीधे तत्वों के संपर्क में नहीं है।

Yes, you can find a wide variety of spare parts available to purchase on our website. If you have any further enquiries, please send an email to support@steadyrack.com and we will be able to provide you with information about parts.

As we use a higher grade of plastic the plastic components of our racks can withstand temperatures within the range of -20 degrees to 70 degrees celcius

Our racks are made to be used under full cover; garages, sheds, or even indoors. Providing that your rack is installed under full cover, it is suitable for coastal conditions. It is recommended that if installing your Steadyrack in coastal conditions that you regularly clean your rack with warm, soapy water to remove any salt build-up which can cause corrosion. Ensure to dry the rack completely after cleaning. Care and maintanence instructions can be found on the installation instructions and on our website. Disclaimer; If you install your racks anywhere they will be directly exposed to the elements including anywhere outside it will void our warranty.

We understand the price can be prohibitive, however our price is as it is for two reasons. The first is that we genuinely believe it reflects the quality and innovation behind our product, and the second is that once you buy a Steadyrack, you have it for life as it is over engineered and built to last (likely longer than your bike!).

Forward your request to partnerships@steadyrack.com and we will be in touch with you shortly.